Severity
Moderate
ModerateActive
CPSC recall · Reported June 9, 2006
Safety Alert: Robert Bosch Tool Corp. Masonry Drill Bits Lack Safety Warning Label
The drill bit packages are not properly labeled with precautionary information on proper use and operation. These and other manufacturers' 13-inch bits can bend when run at a high…
Compiled from official public sources by the editorial team.
Verify with CPSC →
Robert Bosch Tool Corp., Mt. Prospect, Ill. recalled The drill bits are 1/4 inch by 13 inches long, 5/16 inch by 13 inches long, 3/8 inch by 1… - a moderate-severity action.
Safety Alert: Robert Bosch Tool Corp. Masonry Drill Bits Lack Safety Warning Label was recalled by Robert Bosch Tool Corp., Mt. Prospect, Ill. in June 9, 2006. Reason: The drill bit packages are not properly labeled with precautionary information on proper use and operation. T…. Remedy: Consumers should make sure that 13-inch masonry drill bits are in contact with a work sur…. Verify recall #06185 with the CPSC before acting.
The recall
Robert Bosch Tool Corp., Mt. Prospect, Ill. issued this moderate-severity CPSC recall-The drill bit packages are not properly labeled with precautionary information on proper use and operation. T….
- Moderate
- severity level
- June 9, 2006
- reported
Sourced from official CPSC enforcement records. Verify recall #06185 with the agency before acting. Full product description, hazard, remedy, and related recalls are below.
Recall Insight
This CPSC action (record #06185) was formally reported on June 9, 2006. It is classified under Moderate severity, with a current status of Active. Robert Bosch Tool Corp., Mt. Prospect, Ill. is listed as the recalling firm. Federal records list the affected scope as About 700,000.
The documented reason for this recall is: The drill bit packages are not properly labeled with precautionary information on proper use and operation. These and other manufacturers' 13-inch bits can bend when run at a high speed without being in contact with a w… Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. The remedy documented by the agency is: Consumers should make sure that 13-inch masonry drill bits are in contact with a work surface at all times while operating the drill. Consumers with these drill bits that are missing the safety instr… - consumers holding this product should act on that instruction rather than relying on general guidance.
Within the same product category the archive holds 6 closely related recalls, 6 from CPSC - clustering in a narrow category often points to a systemic quality-control or supplier issue rather than a one-off defect. Always verify the recall number against the official agency record before acting.
Household Products recalls over time
Where this recall sits in its category - 3,056 household products recalls on record
Of 101,704 recalls in the database, 24,878 are high severity, 72,426 moderate, and 4,400 low. This recall is classified moderate severity.
Counts reflect market size and reporting activity, not inherent danger, we do not rank products by risk from raw recall volume.
Affected scope
About 700,000
Related Recalls
6
6 from same agency
Product description
The drill bits are 1/4 inch by 13 inches long, 5/16 inch by 13 inches long, 3/8 inch by 13 inches long, and 1/2 inch by 13 inches long. They were sold separately as accessories under the "Vermont American" brand name under catalog numbers: 14044, 14045, 14046, and 14048.
Reason for recall
The drill bit packages are not properly labeled with precautionary information on proper use and operation. These and other manufacturers' 13-inch bits can bend when run at a high speed without being in contact with a work surface, resulting in loss of control of the drill and possible lacerations. The safety label should read: "! WARNING Read, understand and comply with tool manual before use. Wear eye protection. Max operating speed 600 RPM. At higher speeds the bit is likely to bend if allowed to rotate freely without contacting the work. Start drilling at low RPM and with bit tip in contact with work. To avoid bit bowing - Apply pressure only in direct line with bit and do not apply excessive pressure. Bits can bind, causing breakage or loss of control. Do not use in hammer drills or in drill press."
Remedy, what to do
Consumers should make sure that 13-inch masonry drill bits are in contact with a work surface at all times while operating the drill. Consumers with these drill bits that are missing the safety instructions should contact Vermont American Customer Service to obtain safety warning information.
Recall Profile
| Attribute | Value |
|---|---|
| Agency | U.S. Consumer Product Safety Commission |
| Severity class | Moderate |
| Status | Active |
| Recall number | 06185 |
| Date reported | June 9, 2006 |
| Date initiated | June 9, 2006 |
| Recalling firm | Robert Bosch Tool Corp., Mt. Prospect, Ill. |
| Affected scope | About 700,000 |
| Distribution | Not disclosed |
| Official source | CPSC notice → |
Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.
What to do with this recall
Consumers should make sure that 13-inch masonry drill bits are in contact with a work surface at all times while operating the dr…
- Check the recall number (06185) and product description against the item you own. Search the archive
- Confirm the current status and remedy on the official CPSC notice before acting. CPSC notice
- Follow the documented remedy (refund, replacement, repair, or disposal) rather than general advice. What to do next
This page summarizes the official CPSC record for research and awareness; it is not legal, medical, or safety advice. Verify with the issuing agency before acting.
Frequently Asked Questions
What product was recalled? ▼
The drill bits are 1/4 inch by 13 inches long, 5/16 inch by 13 inches long, 3/8 inch by 13 inches long, and 1/2 inch by 13 inches long. They were sold separately as accessories under the "Vermont American" brand name under catalog numbers: 14044, 14045, 14046, and 14048.. Recalled by Robert Bosch Tool Corp., Mt. Prospect, Ill.. Units affected: About 700,000.
Why was this product recalled? ▼
The drill bit packages are not properly labeled with precautionary information on proper use and operation. These and other manufacturers' 13-inch bits can bend when run at a high speed without being in contact with a work surface, resulting in loss of control of the drill and possible lacerations. The safety label should read: "! WARNING Read, understand and comply with tool manual before use. Wear eye protection. Max operating speed 600 RPM. At higher speeds the bit is likely to bend if allowed to rotate freely without contacting the work. Start drilling at low RPM and with bit tip in contact with work. To avoid bit bowing - Apply pressure only in direct line with bit and do not apply excessive pressure. Bits can bind, causing breakage or loss of control. Do not use in hammer drills or in drill press."
What should consumers do? ▼
Consumers should make sure that 13-inch masonry drill bits are in contact with a work surface at all times while operating the drill. Consumers with these drill bits that are missing the safety instructions should contact Vermont American Customer Service to obtain safety warning information.
Which agency issued this recall? ▼
This recall was issued by the CPSC on June 9, 2006. Severity: Moderate. Recall number: 06185.
How do I check if my product is affected by a recall? ▼
Check the product description and recall number (06185) against your product. Visit the official CPSC website for the most current information. You can also use our Recall Checker tool to search by product name or brand.
How do I report an injury from a recalled product? ▼
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.
Nearby Recalls in This Category
Other recalls in the same product category, useful for spotting patterns across the same defect class or manufacturer.
CPSC Moderate
Cooper Lighting Recalls Metalux Optimized High Bay LED Light Fixtures Due to Fire Hazard
Cooper Lighting, LLC, of Peachtree City, Georgia · 2026-07-02
CPSC Moderate
Winco Fireworks International Recalls Roman Candles 8 Shot Fireworks Due to Risk of Serious Injury from Explosion and B…
· 2026-07-02
CPSC Moderate
Winco Fireworks International Recalls Unity 7 Shot 200 Gram Aerial Cake Fireworks Due to Risk of Serious Injury from Ex…
· 2026-07-02
CPSC Moderate
Kith Retail Recalls Children's Loungewear Sets Due to Risk of Serious Injury from Burn Hazard; Violate Mandatory Standa…
· 2026-06-25
CPSC Moderate
Southern Telecom Expands Recall of Lomi Waxing Kits Due to Risk of Serious Injury or Death from Fire and Burn Hazards; …
· 2026-06-25
Compare this recall with Cooper Lighting Recalls Metalux Optimized High Bay LED Ligh… →
Every figure on PlainRecalls is rendered directly from official FDA, CPSC and NHTSA recall records, no number is typed in by an editor. This recall: CPSC, reported June 9, 2006. Severity classes follow each agency's own taxonomy (FDA Class I/II/III; CPSC and NHTSA by hazard type), and related-recall context is computed across the full archive. See our editorial standards & corrections policy, the methodology behind these numbers, or report a data error. Data current as of July 2026.