PlainRecalls
No agency classActive

CPSC recall · Reported April 29, 2008

DEWALT Recalls Table Saws Due to Laceration Hazard

The pivot bracket on the saw can separate, which can misalign the blade and the fence and cause kick back. This poses a laceration hazard to consumers.

Recall #
08259
Affected scope
About 13,000
Verify with CPSC →
View my saved recalls

Dewalt Industrial Tool Co., of Towson, Md. recalled This recall involves the 10-inch DEWALT jobsite table saw model number DW744. Date codes ….

DEWALT Recalls Table Saws Due to Laceration Hazard was recalled by Dewalt Industrial Tool Co., of Towson, Md. in April 29, 2008. Reason: The pivot bracket on the saw can separate, which can misalign the blade and the fence and cause kick back. Th…. Remedy: Consumers should immediately stop using the recalled table saws and contact DEWALT for th…. Verify recall #08259 with the CPSC before acting.

The recall

Dewalt Industrial Tool Co., of Towson, Md. issued this CPSC recall-The pivot bracket on the saw can separate, which can misalign the blade and the fence and cause kick back. Th….

None
agency class
April 29, 2008
reported

Sourced from official CPSC enforcement records. Verify recall #08259 with the agency before acting. Full product description, hazard, remedy, and related recalls are below.

Recall Insight

This recall's affected scope, documented in the Recall Profile below, stays within a single-region or limited-distribution footprint. Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. Consumers holding this product should act on the agency's documented remedy above rather than relying on general guidance.

Within the same product category the archive holds 6 closely related recalls, 6 from CPSC - clustering in a narrow category often points to a systemic quality-control or supplier issue rather than a one-off defect. Always verify the recall number against the official agency record before acting.

Household Products recalls over time

Where this recall sits in its category - 3,089 household products recalls on record

50100150200250 20052008201120142017202020232026 148

Product description

This recall involves the 10-inch DEWALT jobsite table saw model number DW744. Date codes included in the recall are 200715 through 200740. The table saws are yellow and black. The model number and date code are located on the name plate on the front of the saw. Table saws with an "X" stamped on the name plate by the date code are not included in this recall.

Reason for recall

The pivot bracket on the saw can separate, which can misalign the blade and the fence and cause kick back. This poses a laceration hazard to consumers.

Remedy, what to do

Consumers should immediately stop using the recalled table saws and contact DEWALT for the location of a service center to obtain a free replacement table saw.

Recall Profile

Structured summary of the CPSC recall record
Attribute Value
Agency U.S. Consumer Product Safety Commission
Severity class Not classified by agency
Status Active
Recall number 08259
Date reported April 29, 2008
Date initiated April 29, 2008
Recalling firm Dewalt Industrial Tool Co., of Towson, Md.
Affected scope About 13,000
Distribution Not disclosed
Official source CPSC notice →

Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.

What to do with this recall

Consumers should immediately stop using the recalled table saws and contact DEWALT for the location of a service center to obtain…

  • Check the recall number (08259) and product description against the item you own. Search the archive
  • Confirm the current status and remedy on the official CPSC notice before acting. CPSC notice
  • Follow the documented remedy (refund, replacement, repair, or disposal) rather than general advice. What to do next

This page summarizes the official CPSC record for research and awareness; it is not legal, medical, or safety advice. Verify with the issuing agency before acting.

Frequently Asked Questions

What product was recalled?
This recall involves the 10-inch DEWALT jobsite table saw model number DW744. Date codes included in the recall are 200715 through 200740. The table saws are yellow and black. The model number and date code are located on the name plate on the front of the saw. Table saws with an "X" stamped on the name plate by the date code are not included in this recall.. Recalled by Dewalt Industrial Tool Co., of Towson, Md.. Units affected: About 13,000.
Why was this product recalled?
The pivot bracket on the saw can separate, which can misalign the blade and the fence and cause kick back. This poses a laceration hazard to consumers.
What should consumers do?
Consumers should immediately stop using the recalled table saws and contact DEWALT for the location of a service center to obtain a free replacement table saw.
Which agency issued this recall?
This recall was issued by the CPSC on April 29, 2008. CPSC does not publish a hazard classification for this recall. Recall number: 08259.
How do I report an injury from a recalled product?
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.

Nationwide recalls with similar severity or category timing

Consumer-product notices outside this firm and state, matched by severity timing and product category.

Compare this recall with CCM Hockey U.S. Recalls FMHVR Hybrid Visors and ACCHVR Repl… → · All Household Products recalls

This recall: CPSC, reported April 29, 2008. Severity classes follow each agency's own taxonomy; related-recall context is computed across the full archive.

Methodology · Corrections · Archive as of August 2026