PlainRecalls
ModerateActive

CPSC recall · Reported January 22, 2009

Saris Cycling Group Recalls Stationary Bicycle Trainers Due to Fall Hazard

A handle pin on the bicycle trainer can loosen during use, causing the machine to become disengaged, and pose a fall hazard to consumers.

Recall #
09102
Affected scope
2000
Compiled from official public sources by the editorial team.
Verify with CPSC →
View my saved recalls

Saris Cycling Group, of Madison, Wis. recalled The recalled trainers are a stationary frame that allows bicycles to be converted into st… - a moderate-severity action.

Saris Cycling Group Recalls Stationary Bicycle Trainers Due to Fall Hazard was recalled by Saris Cycling Group, of Madison, Wis. in January 22, 2009. Reason: A handle pin on the bicycle trainer can loosen during use, causing the machine to become disengaged, and pose…. Remedy: Consumers with the recalled bicycle trainers should immediately stop using the product an…. Verify recall #09102 with the CPSC before acting.

The recall

Saris Cycling Group, of Madison, Wis. issued this moderate-severity CPSC recall-A handle pin on the bicycle trainer can loosen during use, causing the machine to become disengaged, and pose….

Moderate
severity level
2K units
affected scope
January 22, 2009
reported

Sourced from official CPSC enforcement records. Verify recall #09102 with the agency before acting. Full product description, hazard, remedy, and related recalls are below.

Recall Insight

This CPSC action (record #09102) was formally reported on January 22, 2009. It is classified under Moderate severity, with a current status of Active. Saris Cycling Group, of Madison, Wis. is listed as the recalling firm. Federal records list the affected scope as 2000.

The documented reason for this recall is: A handle pin on the bicycle trainer can loosen during use, causing the machine to become disengaged, and pose a fall hazard to consumers. Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. The remedy documented by the agency is: Consumers with the recalled bicycle trainers should immediately stop using the product and contact Saris Cycling Group to receive a replacement trainer. - consumers holding this product should act on that instruction rather than relying on general guidance.

Within the same product category the archive holds 6 closely related recalls, 6 from CPSC - clustering in a narrow category often points to a systemic quality-control or supplier issue rather than a one-off defect. Always verify the recall number against the official agency record before acting.

Outdoor & Sports recalls over time

Where this recall sits in its category - 510 outdoor & sports recalls on record

101520253035 20052008201120142017202020232026 27
Severity2487872426High severity (most serious)Moderate severityLow severity
Where this recall sits in the database

Of 101,704 recalls in the database, 24,878 are high severity, 72,426 moderate, and 4,400 low. This recall is classified moderate severity.

Counts reflect market size and reporting activity, not inherent danger, we do not rank products by risk from raw recall volume.

Severity

Moderate

Affected scope

2000

Related Recalls

6

6 from same agency

Product description

The recalled trainers are a stationary frame that allows bicycles to be converted into stationary bicycles. The recalled models include: CycleOps Pro Series Trainer models 9014 (SuperMagneto Pro), 9331 (JetFluid Pro), 9460 (PowerBeam Pro), 9321 (JetFluid Pro Winter Training Kit), and 9322 (SuperMagneto Pro Winter Training Kit) without the secondary locking pin. The model number and style names are printed on the left side of the main frame of the trainer.

Reason for recall

A handle pin on the bicycle trainer can loosen during use, causing the machine to become disengaged, and pose a fall hazard to consumers.

Remedy, what to do

Consumers with the recalled bicycle trainers should immediately stop using the product and contact Saris Cycling Group to receive a replacement trainer.

Recall Profile

Structured summary of the CPSC recall record
Attribute Value
Agency U.S. Consumer Product Safety Commission
Severity class Moderate
Status Active
Recall number 09102
Date reported January 22, 2009
Date initiated January 22, 2009
Recalling firm Saris Cycling Group, of Madison, Wis.
Affected scope 2000
Distribution Not disclosed
Official source CPSC notice →

Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.

Scale of Impact

2000 units affected - limited or regional distribution scale.

Regional (<10K units) ✓ This recall
Multi-state (10K – 100K units) -
Large-scale (100K – 1M units) -
Massive (≥1M units) -

Bracket cutoffs follow federal recall-disclosure conventions; bar widths scale linearly within each bracket. Source: PlainRecalls analysis of U.S. Consumer Product Safety Commission filings.

What to do with this recall

Consumers with the recalled bicycle trainers should immediately stop using the product and contact Saris Cycling Group to receive…

  • Check the recall number (09102) and product description against the item you own. Search the archive
  • Confirm the current status and remedy on the official CPSC notice before acting. CPSC notice
  • Follow the documented remedy (refund, replacement, repair, or disposal) rather than general advice. What to do next

This page summarizes the official CPSC record for research and awareness; it is not legal, medical, or safety advice. Verify with the issuing agency before acting.

Frequently Asked Questions

What product was recalled?
The recalled trainers are a stationary frame that allows bicycles to be converted into stationary bicycles. The recalled models include: CycleOps Pro Series Trainer models 9014 (SuperMagneto Pro), 9331 (JetFluid Pro), 9460 (PowerBeam Pro), 9321 (JetFluid Pro Winter Training Kit), and 9322 (SuperMagneto Pro Winter Training Kit) without the secondary locking pin. The model number and style names are printed on the left side of the main frame of the trainer.. Recalled by Saris Cycling Group, of Madison, Wis.. Units affected: 2000.
Why was this product recalled?
A handle pin on the bicycle trainer can loosen during use, causing the machine to become disengaged, and pose a fall hazard to consumers.
What should consumers do?
Consumers with the recalled bicycle trainers should immediately stop using the product and contact Saris Cycling Group to receive a replacement trainer.
Which agency issued this recall?
This recall was issued by the CPSC on January 22, 2009. Severity: Moderate. Recall number: 09102.
How do I check if my product is affected by a recall?
Check the product description and recall number (09102) against your product. Visit the official CPSC website for the most current information. You can also use our Recall Checker tool to search by product name or brand.
How do I report an injury from a recalled product?
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.

Nearby Recalls in This Category

Other recalls in the same product category, useful for spotting patterns across the same defect class or manufacturer.

Compare this recall with Topyond Pool Drain Ports with Covers Recalled Due to Risk o… →

Browse all Outdoor & Sports recalls →

Every figure on PlainRecalls is rendered directly from official FDA, CPSC and NHTSA recall records, no number is typed in by an editor. This recall: CPSC, reported January 22, 2009. Severity classes follow each agency's own taxonomy (FDA Class I/II/III; CPSC and NHTSA by hazard type), and related-recall context is computed across the full archive. See our editorial standards & corrections policy, the methodology behind these numbers, or report a data error. Data current as of July 2026.