PlainRecalls
No agency classActive

CPSC recall · Reported June 25, 2009

DEWALT Recalls Framing Nailers Due to Serious Injury Hazard

The bump action trigger on the framing nailers could have been incorrectly assembled during production, which would allow the nailer to eject a fastener unexpectedly or cause the …

Recall #
09256
Affected scope
About 9,000
Verify with CPSC →
View my saved recalls

Dewalt Industrial Tool Co., of Towson, Md. recalled DEWALT framing nailers with model numbers and date codes listed below: Model Number Descr….

DEWALT Recalls Framing Nailers Due to Serious Injury Hazard was recalled by Dewalt Industrial Tool Co., of Towson, Md. in June 25, 2009. Reason: The bump action trigger on the framing nailers could have been incorrectly assembled during production, which…. Remedy: Consumers should immediately stop using the framing nailers and contact DEWALT for instru…. Verify recall #09256 with the CPSC before acting.

The recall

Dewalt Industrial Tool Co., of Towson, Md. issued this CPSC recall-The bump action trigger on the framing nailers could have been incorrectly assembled during production, which….

None
agency class
June 25, 2009
reported

Sourced from official CPSC enforcement records. Verify recall #09256 with the agency before acting. Full product description, hazard, remedy, and related recalls are below.

Recall Insight

This recall's affected scope, documented in the Recall Profile below, stays within a single-region or limited-distribution footprint. Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. Consumers holding this product should act on the agency's documented remedy above rather than relying on general guidance.

Within the same product category the archive holds 6 closely related recalls, 6 from CPSC - clustering in a narrow category often points to a systemic quality-control or supplier issue rather than a one-off defect. Always verify the recall number against the official agency record before acting.

Household Products recalls over time

Where this recall sits in its category - 3,089 household products recalls on record

50100150200250 20052008201120142017202020232026 148

Product description

DEWALT framing nailers with model numbers and date codes listed below: Model Number Description Date Code Range D51825 Clipped Head Framing Nailer 20080249-20082749 D51850 Full Round Head Framing Nailer 20080249-20082749 The model number and date code are printed on the nailers (see photographs). Nailers with a "T" following the date code and nailers in the original packaging with a green dot identifier on the cardboard packaging are not included in this recall.

Reason for recall

The bump action trigger on the framing nailers could have been incorrectly assembled during production, which would allow the nailer to eject a fastener unexpectedly or cause the trigger lock-off not to function. This can pose a serious injury hazard to the user or bystander.

Remedy, what to do

Consumers should immediately stop using the framing nailers and contact DEWALT for instructions on receiving a free replacement bump action trigger.

Recall Profile

Structured summary of the CPSC recall record
Attribute Value
Agency U.S. Consumer Product Safety Commission
Severity class Not classified by agency
Status Active
Recall number 09256
Date reported June 25, 2009
Date initiated June 25, 2009
Recalling firm Dewalt Industrial Tool Co., of Towson, Md.
Affected scope About 9,000
Distribution Not disclosed
Official source CPSC notice →

Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.

What to do with this recall

Consumers should immediately stop using the framing nailers and contact DEWALT for instructions on receiving a free replacement b…

  • Check the recall number (09256) and product description against the item you own. Search the archive
  • Confirm the current status and remedy on the official CPSC notice before acting. CPSC notice
  • Follow the documented remedy (refund, replacement, repair, or disposal) rather than general advice. What to do next

This page summarizes the official CPSC record for research and awareness; it is not legal, medical, or safety advice. Verify with the issuing agency before acting.

Frequently Asked Questions

What product was recalled?
DEWALT framing nailers with model numbers and date codes listed below: Model Number Description Date Code Range D51825 Clipped Head Framing Nailer 20080249-20082749 D51850 Full Round Head Framing Nailer 20080249-20082749 The model number and date code are printed on the nailers (see photographs). Nailers with a "T" following the date code and nailers in the original packaging with a green dot identifier on the cardboard packaging are not included in this recall.. Recalled by Dewalt Industrial Tool Co., of Towson, Md.. Units affected: About 9,000.
Why was this product recalled?
The bump action trigger on the framing nailers could have been incorrectly assembled during production, which would allow the nailer to eject a fastener unexpectedly or cause the trigger lock-off not to function. This can pose a serious injury hazard to the user or bystander.
What should consumers do?
Consumers should immediately stop using the framing nailers and contact DEWALT for instructions on receiving a free replacement bump action trigger.
Which agency issued this recall?
This recall was issued by the CPSC on June 25, 2009. CPSC does not publish a hazard classification for this recall. Recall number: 09256.
How do I report an injury from a recalled product?
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.

Nationwide recalls with similar severity or category timing

Consumer-product notices outside this firm and state, matched by severity timing and product category.

Compare this recall with CCM Hockey U.S. Recalls FMHVR Hybrid Visors and ACCHVR Repl… → · All Household Products recalls

This recall: CPSC, reported June 25, 2009. Severity classes follow each agency's own taxonomy; related-recall context is computed across the full archive.

Methodology · Corrections · Archive as of August 2026