Severity
Moderate
ModerateActive
CPSC recall · Reported October 18, 2018
Flushmate® Recalls Flushmate II 501-B Pressure-Assisted Flushing Systems Due to Impact and Laceration Hazards
The system can burst at or near the vessel weld seam releasing stored pressure. This pressure can lift the tank lid and shatter the tank, posing impact and laceration hazards to c…
Flushmate, of New Hudson, Mich., a division of Sloan Valve Company recalled This recall is for Flushmate II 501-B pressure-assisted flushing systems installed inside… - a moderate-severity action.
Flushmate® Recalls Flushmate II 501-B Pressure-Assisted Flushing Systems Due to Impact an… was recalled by Flushmate, of New Hudson, Mich., a division of Sloan Valve Company in October 18, 2018. Reason: The system can burst at or near the vessel weld seam releasing stored pressure. This pressure can lift the ta…. Remedy: Consumers should immediately stop using the recalled Flushmate II 501-B systems, turn off…. Verify recall #19012 with the CPSC before acting.
The recall
Flushmate, of New Hudson, Mich., a division of Sloan Valve Company issued this moderate-severity CPSC recall-The system can burst at or near the vessel weld seam releasing stored pressure. This pressure can lift the ta….
- Moderate
- severity level
- October 18, 2018
- reported
Sourced from official CPSC enforcement records. Verify recall #19012 with the agency before acting. Full product description, hazard, remedy, and related recalls are below.
Recall Insight
This CPSC action (record #19012) was formally reported on October 18, 2018. It is classified under Moderate severity, with a current status of Active. Flushmate, of New Hudson, Mich., a division of Sloan Valve Company is listed as the recalling firm. Federal records list the affected scope as About 1.4 million (in addition, about 17,300 were sold in Canada) (The Series 503 Flushmate III was previously recalled June 2012, January 2014, and July 2016.).
The documented reason for this recall is: The system can burst at or near the vessel weld seam releasing stored pressure. This pressure can lift the tank lid and shatter the tank, posing impact and laceration hazards to consumers and property damage. Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. The remedy documented by the agency is: Consumers should immediately stop using the recalled Flushmate II 501-B systems, turn off the water supply to the unit and flush the toilet to release the internal pressure. Consumers should contact … - consumers holding this product should act on that instruction rather than relying on general guidance.
Within the same product category the archive holds 6 closely related recalls - clustering in a narrow category often points to a systemic quality-control or supplier issue rather than a one-off defect. Always verify the recall number against the official agency record before acting.
Drugs & Medications recalls over time
Where this recall sits in its category - 14,287 drugs & medications recalls on record
Of 101,704 recalls in the database, 24,878 are high severity, 72,426 moderate, and 4,400 low. This recall is classified moderate severity.
Counts reflect market size and reporting activity, not inherent danger, we do not rank products by risk from raw recall volume.
Affected scope
About 1.4 million (in addition, about 17,300 were sold in Canada) (The Series 503 Flushmate III was previously recalled June 2012, January 2014, and July 2016.)
Related Recalls
6
0 from same agency
Product description
This recall is for Flushmate II 501-B pressure-assisted flushing systems installed inside toilet tanks that were manufactured from September 3, 1996 through December 7, 2013. The units are rounded oval, black, two-piece vessels made of injection molded plastic. Recalled units have a date code/serial number that is 15 characters long and is located on the label on top of the Flushmate II 501-B unit. The first six numerals of the serial number are the date code. The date code range for units included in this recall in MMDDYY format is 090396 (September 3, 1996) through 120713 (December 7, 2013). The model code is 10 characters long and is located on the same product label. The model code starts with M and ends with F. Units included in this recall were sold individually and installed in toilets manufactured by American Standard, Corona, Crane, Kohler and Mansfield.
Reason for recall
The system can burst at or near the vessel weld seam releasing stored pressure. This pressure can lift the tank lid and shatter the tank, posing impact and laceration hazards to consumers and property damage.
Remedy, what to do
Consumers should immediately stop using the recalled Flushmate II 501-B systems, turn off the water supply to the unit and flush the toilet to release the internal pressure. Consumers should contact Flushmate to request a free Flushmate replacement unit and installation by a technician.
Recall Profile
| Attribute | Value |
|---|---|
| Agency | U.S. Consumer Product Safety Commission |
| Severity class | Moderate |
| Status | Active |
| Recall number | 19012 |
| Date reported | October 18, 2018 |
| Date initiated | October 18, 2018 |
| Recalling firm | Flushmate, of New Hudson, Mich., a division of Sloan Valve Company |
| Affected scope | About 1.4 million (in addition, about 17,300 were sold in Canada) (The Series 503 Flushmate III was previously recalled June 2012, January 2014, and July 2016.) |
| Distribution | Not disclosed |
| Official source | CPSC notice → |
Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.
What to do with this recall
Consumers should immediately stop using the recalled Flushmate II 501-B systems, turn off the water supply to the unit and flush …
- Check the recall number (19012) and product description against the item you own. Search the archive
- Confirm the current status and remedy on the official CPSC notice before acting. CPSC notice
- Follow the documented remedy (refund, replacement, repair, or disposal) rather than general advice. What to do next
This page summarizes the official CPSC record for research and awareness; it is not legal, medical, or safety advice. Verify with the issuing agency before acting.
Frequently Asked Questions
What product was recalled? ▼
This recall is for Flushmate II 501-B pressure-assisted flushing systems installed inside toilet tanks that were manufactured from September 3, 1996 through December 7, 2013. The units are rounded oval, black, two-piece vessels made of injection molded plastic. Recalled units have a date code/serial number that is 15 characters long and is located on the label on top of the Flushmate II 501-B unit. The first six numerals of the serial number are the date code. The date code range for units included in this recall in MMDDYY format is 090396 (September 3, 1996) through 120713 (December 7, 2013). The model code is 10 characters long and is located on the same product label. The model code starts with M and ends with F. Units included in this recall were sold individually and installed in toilets manufactured by American Standard, Corona, Crane, Kohler and Mansfield.. Recalled by Flushmate, of New Hudson, Mich., a division of Sloan Valve Company. Units affected: About 1.4 million (in addition, about 17,300 were sold in Canada) (The Series 503 Flushmate III was previously recalled June 2012, January 2014, and July 2016.).
Why was this product recalled? ▼
The system can burst at or near the vessel weld seam releasing stored pressure. This pressure can lift the tank lid and shatter the tank, posing impact and laceration hazards to consumers and property damage.
What should consumers do? ▼
Consumers should immediately stop using the recalled Flushmate II 501-B systems, turn off the water supply to the unit and flush the toilet to release the internal pressure. Consumers should contact Flushmate to request a free Flushmate replacement unit and installation by a technician.
Which agency issued this recall? ▼
This recall was issued by the CPSC on October 18, 2018. Severity: Moderate. Recall number: 19012.
How do I check if my product is affected by a recall? ▼
Check the product description and recall number (19012) against your product. Visit the official CPSC website for the most current information. You can also use our Recall Checker tool to search by product name or brand.
How do I report an injury from a recalled product? ▼
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.
Nearby Recalls in This Category
Other recalls in the same product category, useful for spotting patterns across the same defect class or manufacturer.
FDA Drug Low
PRED MILD, prednisolone acetate ophthalmic suspension, USP, 0.12%, 10 mL, Sterile, Rx only, Allergen, Inc., an AbbVie c…
AbbVie Inc. · 2026-06-03
FDA Food Moderate
Vitamin B-Complex, Vitamin C & Folic Acid Dietary Supplement, Net Wt. 8 FL Oz (237mL) Amber PET modern round 24-400 bot…
Llorens Pharmaceuticals International Division, Inc. · 2026-05-27
FDA Drug Moderate
Atomoxetine Capsules HCL, 10 mg Capsules in unit dose foil strip, strips are packed in cartons of 100, Rx Only, Pkg by:…
Safecor Health, LLC · 2026-05-27
FDA Drug Moderate
fentaNYL Citrate, Sterile CADD for Injection, 2,2500 mcg/50mL in Sterile Water, IntegraDose Compounding Services LLC, 3…
IntegraDose Compounding Services LLC · 2026-05-27
FDA Drug Moderate
Liraglutide Injection, 18 mg/3 mL (6 mg/mL), Rx only, Manufactured for: Lupin Pharmaceuticals, Inc., Naples, FL 34108, …
Lupin Pharmaceuticals Inc. · 2026-05-27
Compare this recall with PRED MILD, prednisolone acetate ophthalmic suspension, USP,… →
Every figure on PlainRecalls is rendered directly from official FDA, CPSC and NHTSA recall records, no number is typed in by an editor. This recall: CPSC, reported October 18, 2018. Severity classes follow each agency's own taxonomy (FDA Class I/II/III; CPSC and NHTSA by hazard type), and related-recall context is computed across the full archive. See our editorial standards & corrections policy, the methodology behind these numbers, or report a data error. Data current as of July 2026.