Severity
Moderate
ModerateActive
CPSC recall · Reported November 8, 2006
DeWalt Recalls Framing Saws and Circular Saws for Laceration Hazard
The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to consumers.
Compiled from official public sources by the editorial team.
Verify with CPSC →
DeWalt Industrial Tool Co., of Towson, Md. recalled This recall involves DeWalt DW378G and DW378GT 7 ¼-inch framing saws with date codes 2003… - a moderate-severity action.
DeWalt Recalls Framing Saws and Circular Saws for Laceration Hazard was recalled by DeWalt Industrial Tool Co., of Towson, Md. in November 8, 2006. Reason: The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to cons…. Remedy: Consumers should stop using the saws immediately and contact DeWalt for a free repair.. Verify recall #07026 with the CPSC before acting.
The recall
DeWalt Industrial Tool Co., of Towson, Md. issued this moderate-severity CPSC recall-The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to cons….
- Moderate
- severity level
- November 8, 2006
- reported
Sourced from official CPSC enforcement records. Verify recall #07026 with the agency before acting. Full product description, hazard, remedy, and related recalls are below.
Recall Insight
This CPSC action (record #07026) was formally reported on November 8, 2006. It is classified under Moderate severity, with a current status of Active. DeWalt Industrial Tool Co., of Towson, Md. is listed as the recalling firm. Federal records list the affected scope as About 97,000 framing saws and 37,000 circular saws.
The documented reason for this recall is: The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to consumers. Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. The remedy documented by the agency is: Consumers should stop using the saws immediately and contact DeWalt for a free repair. - consumers holding this product should act on that instruction rather than relying on general guidance.
Within the same product category the archive holds 6 closely related recalls, 6 from CPSC - clustering in a narrow category often points to a systemic quality-control or supplier issue rather than a one-off defect. Always verify the recall number against the official agency record before acting.
Electronics recalls over time
Where this recall sits in its category - 609 electronics recalls on record
Of 101,704 recalls in the database, 24,878 are high severity, 72,426 moderate, and 4,400 low. This recall is classified moderate severity.
Counts reflect market size and reporting activity, not inherent danger, we do not rank products by risk from raw recall volume.
Affected scope
About 97,000 framing saws and 37,000 circular saws
Related Recalls
6
6 from same agency
Product description
This recall involves DeWalt DW378G and DW378GT 7 ¼-inch framing saws with date codes 200301-49 through 200637-49. The model numbers for the framing saws are located on the side of the housing. The date code is located either on the name plate or under the handle near the power cord exit. Circular saws involved in this recall have model number DC300 with date codes 200601-49 through 200637-49. The model number on the circular saw is located on the name plate on the top of the motor housing. The date code on the circular saw is located on the underside of the motor housing. Framing saws marked with a "V" on the underside of the handle near the cord set and circular saws marked with a "V" on the underside of the motor housing or under the handle where the battery is inserted have already been repaired and are not involved in this recall.
Reason for recall
The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to consumers.
Remedy, what to do
Consumers should stop using the saws immediately and contact DeWalt for a free repair.
Recall Profile
| Attribute | Value |
|---|---|
| Agency | U.S. Consumer Product Safety Commission |
| Severity class | Moderate |
| Status | Active |
| Recall number | 07026 |
| Date reported | November 8, 2006 |
| Date initiated | November 8, 2006 |
| Recalling firm | DeWalt Industrial Tool Co., of Towson, Md. |
| Affected scope | About 97,000 framing saws and 37,000 circular saws |
| Distribution | Not disclosed |
| Official source | CPSC notice → |
Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.
What to do with this recall
Consumers should stop using the saws immediately and contact DeWalt for a free repair.
- Check the recall number (07026) and product description against the item you own. Search the archive
- Confirm the current status and remedy on the official CPSC notice before acting. CPSC notice
- Follow the documented remedy (refund, replacement, repair, or disposal) rather than general advice. What to do next
This page summarizes the official CPSC record for research and awareness; it is not legal, medical, or safety advice. Verify with the issuing agency before acting.
Frequently Asked Questions
What product was recalled? ▼
This recall involves DeWalt DW378G and DW378GT 7 ¼-inch framing saws with date codes 200301-49 through 200637-49. The model numbers for the framing saws are located on the side of the housing. The date code is located either on the name plate or under the handle near the power cord exit. Circular saws involved in this recall have model number DC300 with date codes 200601-49 through 200637-49. The model number on the circular saw is located on the name plate on the top of the motor housing. The date code on the circular saw is located on the underside of the motor housing. Framing saws marked with a "V" on the underside of the handle near the cord set and circular saws marked with a "V" on the underside of the motor housing or under the handle where the battery is inserted have already been repaired and are not involved in this recall.. Recalled by DeWalt Industrial Tool Co., of Towson, Md.. Units affected: About 97,000 framing saws and 37,000 circular saws.
Why was this product recalled? ▼
The lower blade guard can fail to close, leaving the blade exposed and presenting a laceration hazard to consumers.
What should consumers do? ▼
Consumers should stop using the saws immediately and contact DeWalt for a free repair.
Which agency issued this recall? ▼
This recall was issued by the CPSC on November 8, 2006. Severity: Moderate. Recall number: 07026.
How do I check if my product is affected by a recall? ▼
Check the product description and recall number (07026) against your product. Visit the official CPSC website for the most current information. You can also use our Recall Checker tool to search by product name or brand.
How do I report an injury from a recalled product? ▼
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.
Nearby Recalls in This Category
Other recalls in the same product category, useful for spotting patterns across the same defect class or manufacturer.
CPSC Moderate
Projecting LED Finger Light Toys Recalled Due to Risk of Serious Injury Death from Battery Ingestion; Violate Mandatory…
Shenzhen Bopu Product Design Co., Ltd., dba POPOOO, of China · 2026-07-02
CPSC Moderate
Combination Smoke and Carbon Monoxide (CO) Detectors Recalled Due to Risk of Serious Injury or Death from Failure to Al…
· 2026-06-25
CPSC Moderate
Raychy Children's Light Sneakers Recalled Due to Risk of Serious Injury or Death from Battery Ingestion; Violate Mandat…
· 2026-06-25
CPSC Moderate
Super Off-Road Solar Power Banks Recalled Due to Overheating; Imported by Spector & Co.
· 2026-06-25
CPSC Moderate
School Specialty Recalls Tip Restraint Kits Included in Childcraft Furniture Due to Risk of Serious Injury or Death fro…
School Specialty, LLC, of Greenville, Wisconsin · 2026-06-11
Compare this recall with Projecting LED Finger Light Toys Recalled Due to Risk of Se… →
Every figure on PlainRecalls is rendered directly from official FDA, CPSC and NHTSA recall records, no number is typed in by an editor. This recall: CPSC, reported November 8, 2006. Severity classes follow each agency's own taxonomy (FDA Class I/II/III; CPSC and NHTSA by hazard type), and related-recall context is computed across the full archive. See our editorial standards & corrections policy, the methodology behind these numbers, or report a data error. Data current as of July 2026.