PlainRecalls

Single Meter Sockets Recalled by Milbank Manufacturing Due to Fire and Electrocution Hazards

Reported: October 15, 2009 Initiated: October 15, 2009 #10012 About 1,400 units

Milbank Manufacturing Co., of Kansas City, Mo. issued this CPSC recall on October 15, 2009. Classified as Moderate severity. Approximately About 1,400 units are affected. The recall was issued because: A short may occur while in use due to an incorrect bridge installed in the product, to which the meter clips are attach…. This recall notice is sourced from official CPSC enforcement records. Below you will find the complete product description, hazard information, remedy instructions, and related recalls from the same manufacturer or product category.

Recall Insight

This CPSC action (record #10012) was formally reported on October 15, 2009. It is classified under Moderate severity, with a current status of Active. Milbank Manufacturing Co., of Kansas City, Mo. is listed as the recalling firm. Federal records indicate About 1,400 units are affected.

The documented reason for this recall is: A short may occur while in use due to an incorrect bridge installed in the product, to which the meter clips are attached. If the manufacturing defect exists, all metal parts of the meter could create a shock or burns c… Distribution information was not included in the agency filing, so consumers should assume broad potential exposure until the firm publishes point-of-sale details. The remedy documented by the agency is: Consumers should stop using the recalled product immediately and contact the electrical supply contractor who installed the sockets. Contractors will contact Milbank Manufacturing for a replacement o… — consumers holding this product should act on that instruction rather than relying on general guidance.

To put this record in context, PlainRecalls indexes 83,949 recalls across the FDA, CPSC, NHTSA and USDA FSIS going back to 1995. Within the same product category, the database holds 6 closely related recalls, of which 6 were also issued by CPSC. That clustering is a signal — repeated actions in a narrow category often indicate a systemic quality-control issue, a supplier-wide contamination, or a design defect that has propagated across product lines. This recall is roughly 17 years old; older recalls can remain relevant because many units enter resale, rental, and secondary-market channels where the original warning never reaches the end user. Always cross-check the recall number against the official agency page before relying on any summary.

Recall Distribution by Severity Class

Severity1Class I (Critical)Class II (Moderate)Class III (Low)
Recall Distribution by Severity Class

Severity

Moderate

Units Affected

About 1,400

Related Recalls

6

6 from same agency

Product Description

The single meter 200 amp/4 terminal sockets are used for underground utility meter installations. The meter socket is 20 3/4 inches high by 9 inches wide and 4 1/2 inches deep with 1 meter position. It is used by the approving utility to mount their electric meter to measure how much electricity a residence uses. It can be used for an underground residential application. The recalled model number 9090 appears on the right or left side of the installed meter socket. If not installed, model numbers U9090-O or R9090-O will appear on the label on the outside of the box.

Reason for Recall

A short may occur while in use due to an incorrect bridge installed in the product, to which the meter clips are attached. If the manufacturing defect exists, all metal parts of the meter could create a shock or burns can occur if the cover is off and the meter socket is energized.

Remedy

Consumers should stop using the recalled product immediately and contact the electrical supply contractor who installed the sockets. Contractors will contact Milbank Manufacturing for a replacement or reimbursement. Milbank will contact all distributors and stores where the recalled product was sold.

Recall Profile

Structured summary of the CPSC recall record
Attribute Value
Agency U.S. Consumer Product Safety Commission
Severity class Moderate
Status Active
Recall number 10012
Date reported October 15, 2009
Date initiated October 15, 2009
Recalling firm Milbank Manufacturing Co., of Kansas City, Mo.
Units affected About 1,400
Distribution Not disclosed

Profile values are sourced directly from the official CPSC enforcement record. Source: U.S. Consumer Product Safety Commission.

Scale of Impact

About 1,400 units affected — limited or regional distribution scale.

Regional (<10K units) ✓ This recall
Multi-state (10K – 100K units)
Large-scale (100K – 1M units)
Massive (≥1M units)

Bracket cutoffs follow federal recall-disclosure conventions; bar widths scale linearly within each bracket. Source: PlainRecalls analysis of U.S. Consumer Product Safety Commission filings.

Frequently Asked Questions

What product was recalled?
The single meter 200 amp/4 terminal sockets are used for underground utility meter installations. The meter socket is 20 3/4 inches high by 9 inches wide and 4 1/2 inches deep with 1 meter position. It is used by the approving utility to mount their electric meter to measure how much electricity a residence uses. It can be used for an underground residential application. The recalled model number 9090 appears on the right or left side of the installed meter socket. If not installed, model numbers U9090-O or R9090-O will appear on the label on the outside of the box.. Recalled by Milbank Manufacturing Co., of Kansas City, Mo.. Units affected: About 1,400.
Why was this product recalled?
A short may occur while in use due to an incorrect bridge installed in the product, to which the meter clips are attached. If the manufacturing defect exists, all metal parts of the meter could create a shock or burns can occur if the cover is off and the meter socket is energized.
What should consumers do?
Consumers should stop using the recalled product immediately and contact the electrical supply contractor who installed the sockets. Contractors will contact Milbank Manufacturing for a replacement or reimbursement. Milbank will contact all distributors and stores where the recalled product was sold.
Which agency issued this recall?
This recall was issued by the CPSC on October 15, 2009. Severity: Moderate. Recall number: 10012.
How do I check if my product is affected by a recall?
Check the product description and recall number (10012) against your product. Visit the official CPSC website for the most current information. You can also use our Recall Checker tool to search by product name or brand.
How do I report an injury from a recalled product?
Report injuries to the issuing agency: CPSC at SaferProducts.gov, NHTSA at nhtsa.gov/report-a-safety-problem, or FDA via MedWatch. Document the product (photos, model/serial numbers, purchase receipts) and seek medical attention. Injury reports help agencies track hazard patterns and may strengthen enforcement actions.

Recall Context

Product recalls are issued when a manufacturer, distributor, or federal agency determines that a product poses a safety risk to consumers. This recall is classified as moderate severity, indicating the product may cause temporary or medically reversible health consequences. Across PlainRecalls, we track 83,000+ recalls from FDA, CPSC, and NHTSA to help consumers stay informed and act quickly when safety issues arise.

Nearby Recalls in This Category

Other recalls in the same product category — useful for spotting patterns across the same defect class or manufacturer.

Compare this recall with Electrolux Group Recalls Frigidaire Gas Ranges Due to Burn … →

Data Sources

Data as of 2025. Source: FDA, CPSC, NHTSA, USDA FSIS federal recall databases.

  • Source: FDA — Food and Drug Administration, openFDA Enforcement API (food, drug, and medical device recalls)
  • Source: CPSC — Consumer Product Safety Commission Recalls API (consumer product recalls and hazards)
  • Source: NHTSA — National Highway Traffic Safety Administration Recalls API (vehicle safety recalls)
  • Source: USDA FSIS — Food Safety and Inspection Service (meat, poultry, and egg product recalls)

Recall information is sourced from official federal agency databases. Always verify recall details with the issuing agency for the most current status. This information is for research and awareness purposes only.

All federal data sources used on this page

Source: Federal recall agencies (FDA, CPSC, NHTSA, USDA FSIS) Aggregated multi-agency recall feeds · 2024 Recall data normalized across federal agency feeds; severity classifications follow each agency's own taxonomy (FDA Class I/II/III; CPSC, NHTSA, USDA FSIS).